The Viking 40 Ton "Load Handler" extends the limit for hauling heavy loads. The addition of the third axle extends the GVWR to 100,000 lbs. This trailer is widely used to accommodate a variety of heavy equipment hauling. With a 40 Ton Rating this trailer allows you to haul Dozers, Trac-Hoe's, Back Hoe's, Articulating Loaders, Forklifts, and Large frame Tractors. Like the 35 Ton "Load Handler". This trailer has also proven itself in the Construction, Forestry, and Petroleum industry as a 1st choice for transporting Equipment and Materials from Job to Job. For information on this trailer Click on the Dealer locator to contact a dealer near you.

 Dimensions:

• 46 feet long, 102 inches wide
• 9'-3" upper deck load area
• 28'-11" lower deck load area
• 5' dovetail
• 30 degree drop
• 41" rear deck height

Weight:
               
18,900 lbs. Light +/-3%

Features:

Mainframe 16" Fabricated I-beam with 1/2" x 6 top flange, 3/4" x 6 bottom flange; 1/4" web; All Flange Material is (Grade 130) All Web Material is (Grade 70)

Crossmembers
8" x 6.5# Jr. I-Beam on 20" centers

Kingpin
3/8" king pin plate with 20" setting that allows an 84" swing clearance.

Siderails
12" x 20.7# Structural channel; 8" x 8.5# Structural channel on the neck

Tires
255/70R x 22.5 radials

Wheels
10 hole steel disc; hub piloted wheels

Axles & Brakes
  (3) Rockwell/meritor 25,000#, 5" round; 16 1/2 x 7 service chambers; outboard drums;
WABCO ABS (4S/2M) on two axles

Suspension
Hutch H9700T four point with 365-00 3-leaf Heavy Duty springs.

Lights
   Sealed wiring harness with rubber mounted Incandescent lights. (Optional L.E.D. Lights)

Landinglegs
Holland Mark V; 2 speed with sand shoes; 62,500 lb. lift capacity with handle located on the road side. (Optional location for handle on the curbside)

Metal Covering
1/4" Metal tread plate with 1" traction bars is standard on the dovetail and over the tandem areas. 1/4" Smooth plate with 1" traction bars on the approach to the upper deck.

Dovetail
  5 ft. Covered with 1/4" tread plate with 3/4" traction bars. (Optional Open Floor dovetail with inverted angle iron for self cleaning)

Loading Ramps
  (2) 6' stand up ramps, activated with double compression springs on each ramp that assist in raising and lowering.

Floor 2" nominal oak is standard (Optional Flooring includes: Apitong, Shiplap Pine, Bamboo, Transdeck, and Steel Sheeting)

D-Rings
18 total (14)-1" on rear deck/(4)-1" on front deck]

Finish
    Shotblasted and painted with polyurethane (DTM) Direct to Metal paint (Standard colors are Black, Red, and Cat Yellow)(Optional: Epoxy or Zinc-Rich Primer available)

 Options:

• Hendrickson-Turner HT250US air-ride suspension
• Flooring: Apitong, Shiplap Pine, Bamboo, Transdeck, and Steel Sheeting
• Winches
• Fold out Outriggers
• Width increase to 9'
• Longer and Shorter Lengths
• Between the beam Toolbox
• 4'-6" Lay flat ramps
• 4'-6" Deck level ramps
• Hydraulic assisted ramps
• 36" Deck Height available with 17.5 tires Third ramp located in the center for 3-wheel machines